[Firehol-support] fireqos status shows ERROR ERROR ERROR

[Tsaousis, Costa]

Thanks Mathias!

Well, you can add whatever you like in netdata. Check the
charts.d.plugin. If you know what to add and where to find the source
info, open a github issue in netdata and I'll help you write it.

A good example to start with is `charts.d/squid.chart.sh`.

Costa

PS: I added firehol-support back, so that others can benefit from our
discussion.


On Sat, Sep 26, 2015 at 10:24 PM, Mathias Schulze <mschulze at posteo.de> wrote:
> Hi Costa,
>
> you were right: no more ERRORs when starting fireqos from /etc/ppp/ip-up.d/
>
> Your netdata is great!!!
>
> It would be nice if it could show some information on dhcp leases and
> corresponding wifi signal strenghts.
>
> Thanks,
> Mathias
>
>
> On 09/24/2015 10:01 PM, Tsaousis, Costa wrote:
>> Hi Mathias,
>>
>> Do you leave it running in 'status' mode for a few hours and suddenly
>> it shows ERROR?
>>
>> If this is the case, then most probably the ppp device it monitors has
>> been disconnected (and probably re-connected), but FireQOS has not
>> been re-applied on the re-connected interface yet (QoS is vanished if
>> the interface drops). If you run 'fireqos start' from
>> /etc/ppp/ip-up.d/ then FireQOS will be restarted on the re-connected
>> interface and the 'status' task you run will most probably show a few
>> lines with ERROR and then catch up again.
>>
>> Keep in mind that you can permanently visualize QoS (among hundreds of
>> other Linux system values) with netdata
>> (https://github.com/ktsaou/netdata). This one will give you nice web
>> charts. Check the github page. I recently added a few links to live
>> demos of netdata running.
>>
>> Costa
>>
>>
>>
>> On Thu, Sep 24, 2015 at 10:49 PM, Mathias Schulze <mschulze at posteo.de> wrote:
>>> Hi,
>>>
>>> I use version 2.0.3+ds-1 on a debian machine and I regularly get the
>>> errors below after fireqos was running for a few hours. From what I read
>>> in the list archives such a problem appeared to have been fixed?
>>>
>>> Any help is very much appreciated! I can submit config or other info as
>>> needed.
>>>
>>> Thanks!
>>> Mathias
>>>
>>>
>>> root at apu:/home/mschulze# fireqos status world-out
>>> FireQOS 2.0.3
>>> (C) 2013-2014 Costa Tsaousis, GPL
>>>
>>>
>>> world-out: ppp0 output => ppp0, type: adsl, overhead: 40
>>> Rate: 800Kbit/s, min: 12Kbit/s
>>> Values in Kbit/s
>>>
>>>  CLASS   voip realti    vpn surfin defaul
>>> CLASSI   1:11   1:12   1:13   1:14 1:5000
>>> COMMIT    150     40    160    160     12
>>>    MAX    800    800    800    800    800
>>>
>>> PRIORI      4      4      4      4      4
>>>  QDISC  pfifo fq_cod fq_cod fq_cod fq_cod
>>>
>>>  color code (packets):  backlog  |  dropped  |  delayed  |  requeued
>>>  Class Utilization on world-out (ppp0 output => ppp0) - values in Kbit/s
>>>  TOTAL   voip realti    vpn surfin defaul
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>  ERROR  ERROR  ERROR  ERROR  ERROR  ERROR
>>>
>>> _______________________________________________
>>> Firehol-support mailing list
>>> Firehol-support at lists.firehol.org
>>> http://lists.firehol.org/mailman/listinfo/firehol-support